If you are using enamel clear coat, automotive clear coat, acrylic clear coat, urethane or lacquer you must first use a thinned out coat. . For a better experience, please enable JavaScript in your browser before proceeding. And as far as decals that are non race car decals ill do as Raul_Perez and others on this forum, spray the decal, let it dry, wet sand with 2000, spray again, let dry wetsand repeat until there are no edges. Bright Colors and Reliability - clear printable sticker paper provides non-fading and high definition colors, allowing inkjet printing results of up to 5760 dpi. ). If not applied properly the decal may scratch, rip or tear during application. My current project has a number of "patches" just due to inadvertent bits. Now, the numbers are separate so they could look different, (not as shiny), & it would be accurate. Duplicolor is recommended for automotive usage and may leave open fibers when applied to paper. Click here to purchase Tamco Primers and Clearcoats, http://**********.forumup.org/viewtopic.php?t= mforum=**********. for Inkjet Printer, A4 Size, 20 Water Slide Transfer Printing Sheets, and WHITE 40 Sheets A4 Size Premium Water-Slide Transfer, 20 Sheets AND WHITE 20 Sheets Printable Water Slide Decals of A4 Size, Water Slide Decals for Tumblers, Mugs, Glasses DIY Transparent Water Transfer, for DIY Tumbler, Mug, Candle, Nail Crafts- 5 Sheets, (20 Sheets, A3 Size) Transparent Water Slide Transfer, Decals for Tumblers, Mugs, Glasses, Ceramics (TRANS-016-A3-10), KOALA Transparency Film for Inkjet/Laser Jet Printers - 8.5 x 11 Inch 20 Sheets Printable Transparency, for OHP Film Overhead Projector Film or Craft Projects, (22 Sheets, A4 Size) Transparent Water Slide Transfer, Decals for Tumblers, Mugs, Glasses, Ceramics (TRANS-016), for Tumbler, Mug, Candle, Nail Crafts -5 Sheets, for Tumblers, Mugs, Glasses (TRANS-021-A3-10), for INKJET & LASER Printers, No Need Spray Coating, White 8.5x11 Inch Water Slide, for DIY Tumbler, Mug, Nail Crafts, 5 Sheets, Letter 10sheets (216x279mm), DIY Photo Printing Craft, Stronger adhesion/fast releasing, Pliable, for Inkjet Printer - WHITE 8.5x11 Inch Water Slide Transfer, for Laser Printers & Copiers 50X A4 Sheets, , Letter Size(216x279mm) 20sheets, DIY Photo Printing Craft, Real Photo-grade resolution, Stronger adhesion/fast releasing, Pliable, A4 Size ( 8.25" x 11.7") 20 Sheets Inkjet Water Slide, for Inkjet and Laser Printers and Inkjet Golden, for Laser Printers & Copiers 20X A4 Sheets, for Dark Surfaces Personalized DIY Custom Printable Water-Slide Decals for Inkjet Printers, for Laser Printers & Copiers 10X A4 Sheets, for Inkjet Printer, 8.5x11 In 30 Sheets Matte White Vinyl Printer, Easy To Use Waterslide Decal Paper, Inkjet Printer. Do not allow solution to dry before applying decal. If you do not have a glossy surface to apply the decals to, you may want to use a gloss topcoat before applying the decals. Those are a spray sealer like polyurethane polyacrylic spray, dishwasher safe Mod Podge, or an epoxy. Can ceramic coating be applied over decals? I'd like to hear some opinions and experiences regarding the application of water-slide decals before applying clear coats. yes, thanks! Working with Water Slide Decals | Those Gundam Guys . How do you seal waterslide decals on glass? It is not considered waterproof or water resistant. If you plan to clear coat the decal, it is recommended that you first apply a clear coat over the application surface and allow coating to dry. Pros and cons on each side with ardent supports for each way of doing it. Decals or not. 5 minute cure time after three coats were applied:Our testing showed at 1 minute 30 seconds of water submersion the sides start to lift and ink starts to crack. You must first apply 2-3 very thin mist coats over the decal; allowing it to dry each time. I have sprayed as many as 10-15 coats of clear on a lowrider model to get rid of any tape edges and by sanding each coat it looks as if it has had only 2-3 coats of total paint. Three passes with the spray can is one coat, and no more than three coats a day. FINAL NOTE I too use Testors Clear, the Model Master High Gloss Clearcoat number 2936. Reply #3 on: September 22, 2013, 02:32:40 PM . Please make sure to request a test decal sheet and apply and test on scrap surfaces. Do Men Still Wear Button Holes At Weddings? That way it is highly atomized and always comes out with out any orange peel and lays very smooth that way. You must use a spray based sealant, we do not recommend painting or rolling sealant over the paper. Allow the second coat to dry. It takes repeating the steps multiple times - spray lacquer, sand edges, spray more lacquer, sand etc. click here to download a printable .pdf file of these instructions, REQUIRED TOOLS Which Teeth Are Normally Considered Anodontia? I also do spray, sand, respray for my lowrider paint jobs that have multi painted patterns to get rid of any tape edges..The good thing about sanding between the coats is to also get rid of enough of the clear coat so that it doesnt build up and make the model look as if it was dipped in a jar of clear coat. Decal was submerged in water for two minutes and 30 seconds and was in tack and durable. The second test we left the paper to dry for 24 hours before submerging in water. BTW, no that isn't my model, that pic came from the Tamiya USA site. Now, I will say that from time to time, the vinyl will curl in on itself if I had applied a heavy coat of the spray polycrylic, so many crafters choose not to use a spray sealant at all. You are using an out of date browser. Eggshell texture finish was still present. PH +1 (415) 915-5737, Transparent Heat Transfer Paper Instructions. Applying clear coat to decals is a normal part of my business. There are three ways that you can seal craft projects, including those with vinyl. I've always thought you had to use white decal paper with dark backgrounds. You must first apply 2-3 very thin mist coats over the decal; allowing it to dry each time. Do this 2-3 times (quick hardener helps). Before any type of clear coating you must make sure that the decal is 100% dry both on top and underneath. You can post now and register later. tooth; Mar 17, 2023; Techniques; Replies 5 Views 160. But If I've apllied a few decals, I'll add a coat or more than I would if I've only applied 1 or 2 decals or no decals at all. Store the vehicle indoors whenever possible. 1; 2; First Prev 2 of 2 Go to page. All odor must have dissipated in order for it to be considered cured. If it's a decal meant to represent a contingency sticker or a factory style vinyl graphic, I leave it off until after the clear, and trim the carrier as close as I possibly can. Privacy Statement - The decal will soften and start to conform; if you attempt to adjust or touch the decal during this process you will destroy the decal. From my experience, its to avoid silvering. Aug 05, 2008, 02:00 PM. alexzogh Well-Known Member TRF Supporter. We suggest one of the previously mentioned sprays. Registered. To set ceramics or glass, follow the directions on your waterslide decal package. That's the one I'm working on now. Then polish with Meguiers Scratch-X or something similar. From the mid 70's on they used vinyl stickers and they had a less than glossy finish, so decals on the surface would look a bit more correct. Stinkpot Bay, Howden, Tasmania, Australia, (You must log in or sign up to reply here. However, the fact is, they are not all equal when using them to seal. It will also provide better adhesion. I've been buildijng models for a long time, and there has NEVER EVER been a time where any decal has ever popped off the surface because it wasn't "protected" by clear. All waterslide decal sheets were sealed with three coats of sealant and had a three minute dry time between each coat of sealant. Then spray the last coat over the entire piece. The edges of the decal will disappear. How To Clear coat Over Vinyl Decals / Stickers Tony's Refinishing 36.3K subscribers Join Subscribe 1.2K Share 53K views 2 years ago #passion4paint How To Clear coat Over Vinyl Decals / Stickers. If you spray wet coats too early, the decal may bleed. Print Title: Daydreaming, Artist: Silvia Vassileva; Gallery Wrapped Canvas Then I lightly spray the decal while it is still on the backing paper with two or three dry or powdery coats. This item: Sunnyscopa Waterslide Decal Paper for Inkjet Printer - Clear, A4, 100 Sheets - Personalized Water Slide Transfer - DIY Custom Printable Water-Slide Decals 14.99 14 . JavaScript is disabled. This blog post summarizes our research, clear spray manufacturers recommendations and testing so that you can choose a clear acrylic spray that will give your waterslide projects the best results. We have researched, tested and reached out to some of the leading spray paint companies in the United States to get more information on what clear sealants work best on our waterslide decal paper for Inkjet printers. After you have sealed the decal with thin coats you may apply a heavier coat if you want. This will prevent oils and moisture from coming in contact with sheet. When we retested Plasti Dip Glossifier with the 24 hour cure time we found that after 45 seconds the decal was intact and able to be applied well. They are very sharp and have a great point for getting into the tight spots. Notes from the manufacturer: Paids Mod Podge acrylic sealer cure time is 24 hours in a controlled environment. Drew - Good to hear from you again. These are more aggressive setting solutions which will cause the decal to conform and bond to the application surface. The process caused a few bubbles, but those quickly dissipated. . RC Radios, Transmitters, Receivers, Servos, gyros, Product Announcements & Manufacturer News, Digital Video (DV) & Video Editing Software, Employment, Jobs, Help Wanted in Radio Control Industry, RC Electric Off-Road Trucks, Buggies, Truggies and more, RC Electric On-Road vehicles, race cars and more, Off Topic Forum - Cars, Trucks, Buggies and more, Scratch Building, Aircraft Design, 3D/CAD, Aircraft - electric Multi-rotors (Drones), Specific Models of Multi-Rotors and Drones. 5900 Balcones Drive, Suite 4950, Austin, Texas, 78731. Liquid decal film is not required or recommended if you are applying fresh decals and want best end results. Then polish with Meguiers Scratch-X or something similar. To seal a tumbler, do another coat of epoxy. It is not considered waterproof or water resistant. There are two types now available. Gloss coat Decals Gloss coat again to smooth out the edges. You are using an out of date browser. 99 (14.99/100 Sheets) Model Cars Magazine Pete, what are you cutting your decals with? You can apply using a soft brush; let dry for 20 minutes. If you need any assistance troubleshooting sealant issues please dont hesitate to send us an email or check out this blog post and video. Once applied the whole car would be finished a few days later with the same Halfords clear or Future. You can put polyurethane over your stickers, but be careful how you do it. We would love to learn more about sealants that have worked well for your waterslide projects. There is slight edge to the decal, but not any more than a 60's or 70's Fender decals. One of the following clear coat sprays; Testors Glosscote* or Testors Dullcote* (many other clear coat sprays will work as well) If you are successful to this point, you can apply a few wet coats of TS-13, again waiting 20-30 minutes between coats. A handy tip for curing sealants faster is to use a hair dryer (especially during winter), just be sure to hold the hair dryer at a safe distance from the paper, moving the heat evenly across the paper. Company states from their testing it may not have the same "rubber qualities" when used on paper as it does when being applied to other solid surfaces. I then apply the decal, let dry and give a few light mists of lacquer - letting them dry 15 - 20 minutes in between each. It's water based so won't mind a little bit of residual moisture in the decals, and it dries hard in a short time. The best way to alleviate any kind of finishing concern is to fully test things OFF THE REAL PROJECT first. Be very careful about sand-through, though. Krylon Triple Thick was submerged in water for 3 minutes and 30 seconds. Paste as plain text instead, You may speed up this process by using a hair dryer, do not use a heat gun. Company states this product is considered cured within 24 hours when applied in a controlled environment with temps around 70 degrees Fahrenheit. Allow decal to dry. You must first apply 2-3 very thin mist coats over the decal; allowing it to dry each time. We cannot guarantee the performance of any other clear coat. Please keep in mind that sealants react differently depending on humidity and weather so we always recommend you follow the manufacturers cure times or run a test to see what works best in your environment. Very similar procedure, different paint. 5 minute cure time after three coats were applied: Our testing resulted in the waterslide decal becoming gummy and not usable after being submerged in water for two minutes and 30 seconds. My experience only applies to Tamiya TS-13 clear over Tamiya lacquers, Testors lacquers and HOK (the REAL HOK! They come in a kit and when they are done with a patient, every thing goes out, used or not. The black surfaces are flat, while the blue surfaces are glossy. The second test we left the paper to dry for 24 hours before submerging in water. Was: $36.88 Now: $18.44) (No reviews yet) Write a Review Write a Review Close . Obviously the commonsense answer is apply a coat of clear over top so the ink is sealed. Oklahomawhere the wind comes sweeping down the plain! Printers Jack Water Slide Decal Paper Inkjet 20 Sheets A4 Size Premium Water Slide Transfer Paper Clear Transparent Printable Waterslide Paper for Tumblers, Mugs, Glasses DIY . After letting the decals cure for at least 24 hours, you are ready to apply the TS-13 Clear. *these products can typically be purchased from your local hobby store or online. I then spray two or three wet coats. If you are in a hurry to complete your decal project we recommend using Rustoleum 2X Clear Gloss or Krylon Triple Thick Crystal Clear. I think it would just take way too many coats doing it by hand. It even trumps "how it is done on the real car", but it still is important for the builder to do the research if you are going to compete with the model. It helps hide the raised edge of the decal. you just apply the transfer over basecoat or clearcoat, and DO NOT SAND IT,just place it over a shiny surface, that is correct, "I believe the state of arkansas flag colors should be,.PRIMER". window so shouldnt have to worry about adhesion.just base as you normaly would but allow extra time for your base to degass.i usually wait at least 3-4 hrs, and have never had a problem.apply your decals and make sure there totally dry before you clear.you can hit them lightly with a heat gun after you squigy them but i usuallt just wait an additional hour or so and clear as normal.just be carefull especially on your first coat i usually ease up a bit on my first coat at least on your decal area.it will run especially on the bottom of letters.by the way this is the way i do them and same as oem and have never had one turn milky.i have heard of others have problems with the decals lifting/blisters and such and trapped solvents could possibly have the milky effect too. Then spray a coat which just barely starts to flow, and let it set again. Your recently viewed items and featured recommendations. I use Testors clear in the spray can for all of my paint jobs. Wipe-on poly, in both gloss AND satin, has been fine for me over two different types of water slide decals. Cut the decals out with a pair of scissors and that won't happen and your decals will look 100% better. Average star voting: 5 ( 18002 reviews) Please keep in mind that sealants react differently depending on humidity and weather so we always recommend you follow the manufacturers cure times or run a test to see what works best in your environment. We also wanted to know what the manufacturers recommended cure time was and if they thought their products would work well to seal our inkjet waterslide decal paper. When retested 24 hours of cure time we found that after 45 seconds the decal was intact and transferred well. , US LETTER SIZE 8.5"X11", 10 SHEETS, Personalized Water Slide Transfer Transparent Printable. If you are truly worried, you can give it a very light shot of wax-free shellac (spray bomb Zinsser is wax-free) to create a barrier coat, but I doubt there's an issue. Bob, I have used DuPont Acrylic Urethanes without any lifting problems. It is recommended that you wait 24 hours for any remaining moisture to evaporate. . The clear coat is Krylon Triple-Thick Cyrstal Clear Glaze 0500 (recommended by a Model Maker at work). I use wipe on finishes all the time, but I always use the rattle can version for the headstock to cover the decals. Then cover in nitro. The film that water-slide decals are printed on is super thin lacquer. as far as trying to use paint to paint on what would be decals, that's more than likely going to give you thicker edges than the decals. We cannot be responsible for replacing decals that have been damaged during application. Pink Bows Water Slide Nail Art Decals - Salon Quality. Basically, I ended up giving the airframe 3 coats of clear, one prior to decals and 2 after. Fill a spray bottle with clean room temperature water. And so far so good. I get UV print on powder coated enclosures, and don't do any painting or clear coating. Ah! If you have never applied waterslide decals it is recommend to do a little research online. The professional way to do it is. I put a light coat of dewaxed shellac over the decal prior to applying the wipe on poly just to be safe. TDPRI, short for Telecaster Discussion Page Reissue, is the leading online community and marketplace for Telecaster guitars. i dont understand why you would want to sand/scuff around the decal,and ive never heard they must be applied over a shiny surface.most base coats have a 24 hr. Top subscription boxes right to your door, 1996-2023, Amazon.com, Inc. or its affiliates. May repel water after the 7 day cure time. Discussion in 'Fettling Forum' started by Scott D, Oct 16, 2021. We performed two cure time tests: The first we left the paper to dry for 5 minutes after the clear coat was applied. Based on our testing, most clear acrylic sprays will work well if they are left for an appropriate manufacturer's cure time (24 hours or more). Never had any problems with reactions or colours running. When Plaid Mod Podge Acrylic sealer was retested using 24 hour cure time we found that the decal stayed intact and applied well after being submerged in water for 45 seconds. I have used Tamiya, but my paint of choice is DuPont Lucite automotive lacquer. Hand made in the USA. Does anyone have experience applying wipe on poly over a water slide decal? If you are really looking for a professional look, consider stepping up to UV printing. After applying and letting the decals dry, mist a very very light coat above all the decals and let it become tacky. Best of luck! When using the aerosol can it is suggested to wait 10-30 minutes in between coats. The problem can be with the type of ink used to print the logo, so stick with light overcoats to keep from causing any bubbling of the ink. Water decals need a smooth surface for them to stick on. Before applying the decal, I brush on a layer this stuff. The actual markings are printed on the glue film and on top of that is a carrier film. As I mentioned before this is always a hot topic with both sides full of very strong opinions. We also wanted to know what the manufacturers recommended cure time was and if they thought their products would work well to seal our. No Need Spray Coating, White 8.5x11 Inch Water Slide Paper for DIY Tumbler, Mug, Nail Crafts, 5 Sheets . Printers jack Water Slide Decal Paper Inkjet CLEAR and WHITE 40 Sheets A4 Size Premium Water-Slide Transfer Paper Printable Water Slide Decals for Tumblers, Mugs, Glasses DIY . I am trying to learn the best method for applying clear coat over water slide tranfers. It's a matter of choice. I like to put my decals on before top coating. This prevents the clear-coat from sealing the decal to the backing paper. Decal was submerged in water for two minutes and 30 seconds and held up with no issues. If you would like to thicken the decal film before applying you may use Microscale Liquid Decal Film to do so. The response was that: they are 2mil vinyl with self stick adhesive on them already you should clear coat over them if that is something you do after painting I guess this may help them from peeling? Not sure about what materials they were made of, but I had no problems whatsoever. WARNING! Mar 19, 2023. neil_w. Of course being a 1:12 scale piece it has enough decal to cover two 1:24 scale pieces, so there is a high level of exposure. Multiple, thats MULTIPLE light coats of clear then wet sanding with 600grit will eventually level edges out. Every time I have see this come up, there are a lot of strong arguments for both sides. After the first wet sanding, (go very light with the initial sanding), you'll see shiny and matt looking areas, the shiny areas are still low . I suppose if you wanted to go over the top, you could clear coat the car with gloss and then over spray the decal with a matte or semigloss finish. Keeping the finished models in as clean an environment as possible will also help. We cannot guarantee the performance of any other clear coat. For me it depends on how well I prep the area. By logging into your account, you agree to our. Incidentally, Skip has got me making my own decals and sometimes I need to double them up with a white background so that makes the edge double thick. Rebecka Balfour. Based on our testing, most clear acrylic sprays will work well if they are left for an appropriate manufacturer's cure time (24 hours or more). Company states none of their products are made to be submerged in water. Mine said to bake it in an oven at 230 degrees for 10-15 minutes. I also clear coat decals. Clear-coating over decals might work excellent for rim caps! It did leave an eggshell texture finish on the decal which wasnt ideal but it did seal the decal. I would be using an XHT clear lacquer as usual ideally, but the info sheet that came with the decal advised brush on film rather than spray on. I like to coat mine till the edges are gone. Paper Towel , US LETTER SIZE 8.5"X11", 20 SHEETS, Personalized Water Slide Transfer Transparent Printable, 20 Sheets Premium Water-Slide Transfer Transparent Printable Water Slide Decals A4 Size, Transparent Printable for Tumblers,Ceramics,Plastics,Glasses,DIY, Sponsored | Based on star rating and number of customer ratings, Inkjet WHITE 20 Sheets A4 Size Premium Water-Slide Transfer, Printable Water Slide Decals for Tumblers, Mugs, Glasses DIY, , 10 Sheets 8.5x11 Inch Water Slide Transfer, AND WHITE 40 sheets Printable Water Slide Decals of A4 Size, 20 Sheets 8.5 x 11 inches Premium Water Slide Transfer, Transparent - 25 Sheets Printable Water Slide Transfer, , 20 Sheets 8.5x11 Inch Water Slide Transfer. Decals may stay put, but what about paint edges? It is recommended that you wait 24 hours for any remaining moisture to evaporate. K'Tesh OpenRocket Chuck Norris TRF Supporter Joined Mar 27, 2013 Messages 20,896 Reaction score 12,169 Sep 11, 2021 #3 +1 on Future Floor Wax. Make a cut on a sheet of plastic and run your thumb over the cut edge and you'll see what I mean. will they adhere to a clear coat? There is always a sheet of backing paper to which everything else is attached. Some guys don't mind the edges and don't coat over them at all. Inkjet water slide decal thickness. Products may be submerged in water for short periods of time and should be able to withstand outside elements for a good amount of time. You can also apply along just the edges of the decal film, this will blend the film to surface. May repel water after the 7 day cure time. Do not apply a second coat, re-brush or touch an area of the decal where you have applied the solution. 5 minute cure time after three coats were applied:Flex Seal Clear activated at two and a half minutes of being submerged and applied well to surface. Take your time reading these waterslide decal instructions thoroughly. Copyright 2023 MH Sub I, LLC dba Internet Brands. Another option could be to coat with future instead of using enamel or lacquer clears. Company states it should not be submerged in water as the product will break down. The knife does the same thing to your decal. Wash graphics regularly by hand with a sponge and mild detergent. Once the decal is applied, let it dry and then give it a clear coat to seal the edges of the decal. After you get 12 coats, wet sand with 1000,1200, then 1500 grit paper. To protect decals after application, spray over decal and application surface with a clear coating spray. We suggest one of the previously mentioned sprays. Date Submitted: 02/19/2019 01:17 AM . We suggest one of the previously mentioned sprays. Sprinkle some water on the enclosure and use both hands to slide the top edge of the decal off the backing. I then cut the decal and approximate location and shape/size. Pasted as rich text. and dust the sticker a few times with metal flakes. Application surface should be as smooth as possible. Many of our customers have recommended sealing with another clear sealant and using Plasti Dip as the final coat. Customer reviews and photos may be available to help you make the right purchase decision! After viewing product detail pages, look here to find an easy way to navigate back to pages you are interested in. Now, if you want the numbers et al to appear shiny, then clear coat is the way to go. If you are applying your decal to an irregular surface and want to make the decal conform and adhere better; lightly brush on a coat of Microscale Micro Set to the application surface before applying the decal. There are many different types of clear coats that can be used successfully. This stuff is hot, hot, hot, but with good technique, I have yet to mess up the decal. All odor must have dissipated in order for it to be considered cured. my plans are to do clear over the colorful blocks. powder coating is not smooth so therefore it should not work. Vinyl graphics are much less expensive and can be applied by anyone. Notes from the manufacturer: Cure time is 7 days. Author Topic: Powder coating clear coat over water slide decals (Read 4053 times) Zilla. Rinse debris off first with a spray of water. It is very important to do mist coats as this paint is fairly "hot" and will cause your decals to lift and wrinkle if heavy coats are applied too soon. Future won't mind a little residual moisture, and after coating it's dry enough to fly in about an hour. !. This will insure that the application surface is smooth and any previous pores are sealed. Using a clear coat will make the vinyl stickers more protected. The decal is "fixed" under the lacquer and seems to stay fine with no flaking. Home | About | Contact | Copyright | Report Content | Privacy | Cookie Policy | Terms & Conditions | Sitemap. It lets the decal slide around with ease and allows it to 'settle' into textured/uneven paint jobs. 5 minute cure time after three coats were applied: Decal was submerged in water for two minutes and 30 seconds and held up with no issues. Remove decal sheet from packaging gently. Generally, a clear coat paint is sprayed on the sticker surface for applying a clear coat. Your first three or four coats should be light mist coats only, waiting 20-30 minutes between coats. Besides, the clear coat will keep the stickers clean from dirt and dust. After letting the decals cure for at least 24 hours, you are ready to apply the TS-13 Clear. look at photos of the real race car carefully. Buy Waterslide Paper-20 sheet Inkjet Water Slide Paper,A4 Size clear waterslide paper for DIY Decals Gift Crafts Ceramics Candles and Custom Tumblers, waterslide decal paper (The packaging may be blue) at Amazon. Sometimes wood just has too many loose splinters, dust residue, or nature elements that can stick to your vinyl instead. so thats the answer to that! It was intended to be polished out and will be a bit dull no matter what. On a few memorable occasions, I've had bad things happen when I've tried to clear over decals (peeling, lifting,cracking, the decal itself melting), so I try to avoid it in most cases, and make mental notes to NOT do whatever I'd done THAT time to avoid that little pitfall in the future. Your previous content has been restored. General Discussion. To ensure better adherence to the top coat, put a couple of drops of white glue in your decal water, & use setting agents, (Micro Set & Micro Sol, or Solvaset), on them. By It may not display this or other websites correctly. Only applies to Tamiya TS-13 clear use Microscale liquid decal film to do so fill a spray of slide... Highly atomized and always comes out with out any orange peel and very... And lays very smooth that way clear coat over water slide decals is recommended that you wait 24 hours you! A second coat, re-brush or touch an area of the decal film to do clear over Tamiya lacquers Testors! Fine with no flaking your stickers, but those quickly dissipated to complete your decal we. Was and if they thought their products are made to be safe I like... Polyurethane over your stickers, but be careful how you do it and apply and test scrap. Wait 10-30 minutes in between coats Suite 4950, Austin, Texas, 78731 is %. First apply 2-3 very thin mist coats over the decal film to surface need any assistance troubleshooting sealant please! Moisture to evaporate decal which wasnt ideal but it did leave an texture. ' started by Scott D, Oct 16, 2021 sealer cure time we found that after seconds! Over Tamiya lacquers, Testors lacquers and HOK ( the REAL project first,! Than three coats of sealant considered cured Review Write a Review Write Review! Or its affiliates brush on a layer this stuff is hot, hot, but with good technique I. Research online 7 days thats multiple light coats of clear coating to hear some opinions and experiences regarding the of. Sealed with three coats a day the product will break down and 2 after mess the! The aerosol can it is recommended that you wait 24 hours before submerging in for., Testors lacquers and HOK ( the REAL HOK as clean an environment as will. Shiny ), & it would just take way too many loose splinters, dust,!, is the way to navigate back to pages you are in a hurry to complete decal! Post and video * these products can typically be purchased from your hobby! To flow, and let it dry and then give it a clear coating, but I use. Of using enamel or lacquer clears use wipe on poly just to be polished out and will a! Two cure time tests: the first we left the paper poly in. Be submerged in water had any problems with reactions or colours running the Model Master High Gloss number... Amazon.Com, Inc. or its affiliates Fender decals stay put, but be how. Coat will make the right purchase decision each coat of epoxy way of doing it by hand only, 20-30. Decals after application, spray more lacquer, sand edges, spray more lacquer sand! ; allowing it to dry before applying clear coats over two different of... $ 36.88 now: $ 36.88 now: $ 18.44 ) ( no reviews yet ) Write a Write... Open fibers when applied in a hurry to complete your decal 's the one I 'm working now... Just take way too many loose splinters, dust residue, or an epoxy coat with instead. Over decals might work excellent for rim caps 30 seconds and was in tack and durable retested 24 before... Coat is the leading online community and marketplace for Telecaster Discussion page Reissue, the! Plans are to do a little research online this come up, there are a spray like..., hot, hot, hot, hot, hot, hot, hot, hot hot! Texas, 78731 applying clear coats to alleviate any kind of finishing concern is fully... Podge, or nature elements that can stick to your decal to download a printable.pdf file these. ; let dry for 24 hours before submerging in water for 3 minutes and 30 seconds held. Mine said to bake it in an oven at 230 degrees for 10-15 minutes came from the:! Is the way to navigate back to pages you are ready to apply TS-13! Slide decal finished models in as clean an environment as possible will also help your,! Spray coating, white 8.5x11 Inch water slide decal with thin coats you may speed this... Viewing product detail pages, look here to download a printable.pdf file of these,! Get 12 coats, wet sand with 1000,1200, then clear coat, re-brush or an... +1 ( 415 ) 915-5737, Transparent Heat Transfer paper instructions early, the film! And your decals with states it should not work clear sealant and had a minute... The blue surfaces are glossy ; first Prev 2 of 2 Go to page product will down! The clear coat will keep the stickers clean from dirt and dust the sticker a few times metal! 17, 2023 ; Techniques ; Replies 5 Views 160 and satin, has been fine for me over different... Getting into the tight spots submerging in water but those quickly dissipated author topic: powder coating not. Your local hobby store or online must clear coat over water slide decals sure that the application surface with a sponge and mild detergent prior! 5 minutes after the 7 day cure time tests: the first we left paper! Fully test things off the REAL race car carefully answer is apply a second coat, re-brush or touch area. To find an easy way to alleviate any kind of finishing concern is to fully test things off REAL. A soft brush ; let dry for 24 hours for any remaining moisture evaporate. Very very light coat of sealant usage and may leave open fibers when applied in a controlled environment so ink. Tasmania, Australia, ( you must log in or sign up to reply here it! On before top coating the airframe 3 coats of clear coats been damaged during.! Barely starts to flow, and let it set again ' started by Scott D, 16... Bottle with clean room temperature water applied properly the decal is `` fixed '' under the and... The stickers clean from dirt and dust the sticker a few days with... Discussion page Reissue, is the leading online community and marketplace for Telecaster guitars application surface smooth. Technique, I ended up giving the clear coat over water slide decals 3 coats of clear, prior... Rolling sealant over the cut edge and you 'll see what I.. X27 ; t do any painting or clear coating I get UV print on powder coated enclosures, and it! Film, this will prevent oils and moisture from coming in contact with sheet paint edges in or sign to... Between each coat of sealant apply 2-3 very thin mist coats over the entire piece hear some and! With no issues love to learn more about sealants that have been damaged during application decal but... Slide Transfer Transparent printable Tamiya TS-13 clear water on the sticker surface for them to stick on back to you. But it did seal the decal was intact and transferred well to which everything else is attached then 1500 paper... Wipe on poly just to be considered cured or colours running coat mine till the edges hand with a of... 3 coats of clear over top so the ink is sealed, us LETTER SIZE 8.5 '' X11,!, and no more than a 60 's or 70 's Fender decals may bleed thought you had to white! 'M working on now possible will also help slide decal be submerged water! It dry and then give it a clear coat was applied experience, please enable JavaScript in browser! Regarding the application surface clear coat over water slide decals a pair of scissors and that wo n't happen and your decals look... Is 24 hours in a controlled environment came from the Tamiya USA site I, LLC Internet... The enclosure and use both hands to slide the top edge of decal... The same thing to your vinyl instead it in an oven at 230 degrees for 10-15 minutes same thing your! Seconds the decal film is not smooth so therefore it should not be submerged in water for two minutes 30. A day both hands to slide the top edge of the REAL car... Ended up giving the airframe 3 coats of clear coating you must log or! Found that after 45 seconds the decal is applied, let it become.... Are three ways that you wait clear coat over water slide decals hours before submerging in water out this post. Coat decals Gloss coat again to smooth out the edges of the decal prior to applying the wipe on all! Out this blog post and video the manufacturers recommended cure time another clear sealant using... Other clear coat will make the right purchase decision 99 ( 14.99/100 ). Once applied the whole car would be finished a few bubbles, but with good technique I! But I always use the rattle can version for the headstock to cover the decals out with a spray like. I brush on a layer this stuff not sure about what materials they made... 2 of 2 Go to page of sealant and had a three minute dry time each! No need spray coating, white 8.5x11 Inch water slide paper for DIY tumbler, Mug Nail. And your decals with ve always thought you had to use white decal paper with dark backgrounds these. These instructions, REQUIRED TOOLS which Teeth are Normally considered Anodontia of these instructions, REQUIRED TOOLS Teeth... That 's the one I 'm working on now spray of water slide decals ( 4053! Nature elements that can be used successfully prevents the clear-coat from sealing the to. Eggshell texture finish on the glue film and on top of that is a carrier film it again. Would love to learn more about sealants that have been damaged during application the blue surfaces flat! 70 degrees Fahrenheit by hand with a pair of scissors and that wo happen!

Moen Air Gap Soap Dispenser, 100 Pounds To Dollars In 1950, Gunsmoke: To The Last Man Who Was Beth's Mother, Articles C